ref: e12cb95079f001aae1b1eeecd2463ccc61da1c30
dir: /doc/asm/macro.htm/
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2//EN">
<HTML>
<HEAD>
<TITLE>xAsm MACRO/ENDM</TITLE>
</HEAD>
<BODY BGCOLOR="#692764" TEXT="#F5A0D8" LINK="#8AAEE6" VLINK="#2B9DA4" ALINK="#95F0DA">
<I><H2>MACRO<BR>
ENDM</H2></I><HR>
<P>One of the best features of an assembler is the ability to write macros for it. Macros also provide a method of passing
arguments to them and they can then react to the input using IF-constructs.<BR>
<BR>
<TABLE BORDER=0 BGCOLOR="Black" CELLPADDING=8 WIDTH="50%">
<TR>
<TD><FONT COLOR="#00FF00">
<PRE>MyMacro: MACRO
ld a,80
call MyFunc
ENDM</PRE>
</FONT></TD>
</TR>
</TABLE>
<P>The above example is a very simple macro. You execute the macro by typing its name.<BR>
<BR>
<TABLE BORDER=0 BGCOLOR="Black" CELLPADDING=8 WIDTH="50%">
<TR>
<TD><FONT COLOR="#00FF00">
<PRE> add a,b
ld sp,hl
MyMacro ;This will be expanded
sub a,87</PRE>
</FONT></TD>
</TR>
</TABLE>
<P>When the assembler meets MyMacro it will insert the macrodefinition (the text enclosed in <B>MACRO/ENDM</B>).
<P><A NAME="labelsuffix"></A>Suppose your macro contains a loop.<BR>
<BR>
<TABLE BORDER=0 BGCOLOR="Black" CELLPADDING=8 WIDTH="50%">
<TR>
<TD><FONT COLOR="#00FF00">
<PRE>LoopyMacro: MACRO
xor a,a
.loop ld [hl+],a
dec c
jr nz,.loop
ENDM</PRE>
</FONT></TD>
</TR>
</TABLE>
<A TARGET="#labelsuffix"></A><P>This is fine. That is, if you only use the macro once per <A HREF="labels.htm">scope</A>. To get around this problem there is a special label string equate called <B>\@</B> that you can append to your labels and it will then expand to a unique string.
<B>\@</B> also works in <A HREF="rept.htm">REPT-blocks</A> should you have any loops there.<BR>
<BR>
<TABLE BORDER=0 BGCOLOR="Black" CELLPADDING=8 WIDTH="50%">
<TR>
<TD><FONT COLOR="#00FF00">
<PRE>LoopyMacro: MACRO
xor a,a
.loop\@ ld [hl+],a
dec c
jr nz,.loop\@
ENDM</PRE>
</FONT></TD>
</TR>
</TABLE>
<H4>Arguments</H4>
<P>I'd like <I>LoopyMacro</I> a lot better if I didn't have to pre-load the registers with values and <I>then</I> call it.
What I'd like is the ability to pass it arguments and it then loaded the registers itself.
<P>And I can do that. In macros you can get the arguments by using the special macro string equates <B>\1</B> through
<B>\9</B>, <B>\1</B> being the first argument specified on the calling of the macro.<BR>
<BR>
<TABLE BORDER=0 BGCOLOR="Black" CELLPADDING=8 WIDTH="50%">
<TR>
<TD><FONT COLOR="#00FF00">
<PRE>LoopyMacro: MACRO
ld hl,\1
ld c,\2
xor a,a
.loop\@ ld [hl+],a
dec c
jr nz,.loop\@
ENDM</PRE>
</FONT></TD>
</TR>
</TABLE>
<P>Now I can call the macro specifying two arguments. The first being the address and the second being a bytecount.
The macro will then reset all bytes in this range.<BR>
<BR>
<TABLE BORDER=0 BGCOLOR="Black" CELLPADDING=8 WIDTH="50%">
<TR>
<TD><FONT COLOR="#00FF00">
<PRE> LoopyMacro MyVars,54</PRE>
</FONT></TD>
</TR>
</TABLE>
<P> You can specify up to nine arguments when calling a
macro. Arguments are passed as string equates. There's no need to enclose them in quotes. Parameter passing has changed a bit since v1.03 in that an expression will not be evaluated first but passed directly. This means that it's probably a very good idea to use
brackets around \1-\9 if you perform further calculations on them. For instance if you pass 1+2 as the first argument and then do
<P><TABLE BORDER=0 BGCOLOR="Black" CELLPADDING=8 WIDTH="50%">
<TR>
<TD><FONT COLOR="#00FF00">
<PRE> PRINTV \1*2
</PRE>
</FONT></TD>
</TR>
</TABLE>
you will get the value 5 on screen and not 6 as you might have expected..<BR>
<P>Note that a colon (:) following the macro-name is required. Macros can't be exported or imported. It's valid to call a macro from a macro (yes, even the same one).<BR>
<H3>See also:</H3>
<UL>
<LI><A HREF="shift.htm">SHIFT</A>
</UL>
<BR><HR>
<FONT SIZE="-1"><I><P ALIGN=RIGHT>Last updated 02 July 1997 by <A HREF="mailto:[email protected]">Carsten Sorensen</A></P></I></FONT>