ref: 2af6b0896040ab24c2d411a36781d7588935c6cf
dir: /sys/man/3/mouse/
.TH MOUSE 3 .SH NAME mouse, cursor \- kernel mouse interface .SH SYNOPSIS .nf .B bind -a #m /dev .B /dev/mouse .B /dev/mousein .B /dev/mousectl .B /dev/cursor .fi .SH DESCRIPTION The .I mouse device provides an interface to the mouse. There is also a cursor associated with the screen; it is always displayed at the current mouse position. .PP Reading the .B mouse file returns the mouse status: its position and button state. The read blocks until the state has changed since the last read. The read returns 49 bytes: the letter .B m followed by four decimal strings, each 11 characters wide followed by a blank: .I x and .IR y , coordinates of the mouse position in the screen image; .IR buttons , a bitmask with the 1, 2, and 4 bits set when the mouse's left, middle, and right buttons, respectively, are down; and .IR msec , a time stamp, in units of milliseconds. .PP Writing the .B mouse file, in the same format, causes the mouse cursor to move to the position specified by the .I x and .I y coordinates of the message. The .I buttons and .I msec fields are ignored and may be omitted. .PP Writes to the .B mousein file are processed as if they were generated by the mouse hardware itself, as extra mouse events to be processed and passed back via the .B mouse file. The .B mousein file, which is exclusive-use and may be opened only by the host owner, is intended for controlling devices, such as USB mice, that are managed by user-level software. Each event should consist of the letter .B m followed by delta .IR x , delta .IR y , and .IR buttons as space-separated decimal numbers. .PP Writing to the .B mousectl file configures and controls the mouse. The messages are: .TF ps2intellimouse .TP .B "serial\fI n\fP" sets serial port .I n to be the mouse port. .TP .B ps2 sets the PS2 port to be the mouse port. .TP .B intellimouse uses the wheel on a Microsoft Intellimouse as the middle button. .TP .B ps2intellimouse is equivalent to a write of .B ps2 followed by a write of .BR intellimouse . .TP .B "accelerated\fI [n]\fP" turns on mouse acceleration. .I N is an optional acceleration factor. .TP .B linear turns off mouse acceleration. .TP .B "res\fI n\fR" sets mouse resolution to a setting between 0 and 3 inclusive. .TP .B "hwaccel\fI on/off\fP" sets whether acceleration is done in hardware or software. By default, PS2 mice use hardware and serial mice use software. Some laptops (notably the IBM Thinkpad T23) don't implement hardware acceleration for external mice. .TP .B swap swaps the left and right buttons on the mouse. .TP .B "buttonmap\fI xyz\fP" numbers the left, middle, and right mouse buttons .IR x , .IR y , and .IR z , respectively. If .I xyz is omitted, the default map, 123, is used. Thus in the default state writing .B "buttonmap 321 swaps left and right buttons and writing .B "buttonmap 123 or just .B buttonmap restores their usual meaning. Note that .B buttonmap messages are idempotent, unlike .BR swap . .TP .B reset clears the mouse to its default state. .TP .B blank Blank the screen. The screen also blanks after 30 minutes of inactivity. The screen can be unblanked by moving the mouse. .TP .BI blanktime " minutes" Set the timeout before the screen blanks; the default is 30 minutes. If .I minutes is zero, blanking is disabled. .TP .B twitch unblanks the screen and resets the idle timeout as if the mouse was twitched. .PD .PP Not all mice interpret all messages; with some devices, some of the messages may be no-ops. .PP Cursors are described in .IR graphics (2). When read or written from or to the .B cursor file, they are represented in a 72-byte binary format. The first and second four bytes are little endian 32-bit numbers specifying the .I x and .I y coordinates of the cursor .IR offset ; the next 32 bytes are the .B clr bitmask, and the last 32 bytes the .B set bitmask. .PP Reading from the .B cursor file returns the current cursor information. Writing to the .B cursor file sets the current cursor information. A write of fewer than 72 bytes sets the cursor to the default, an arrow. .PP The .B mouse and .B cursor files are multiplexed by .IR rio (1) to give the illusion of a private mouse to each of its clients. The semantics are otherwise the same except that notification of a window resize is passed to the application using a .B mouse message beginning with .B r rather than .BR m ; see .IR rio (4) for details. .PP To cope with pointing devices with only two buttons, when the shift key is pressed, the right mouse button generates middle-button events. .SH SOURCE .B /sys/src/9/port/devmouse.c .SH "SEE ALSO .IR rio (4) .SH BUGS The cursor format is big endian while the rest of the graphics interface is little endian.