shithub: riscv

ref: 53d55013598d7cd214d01cbf0b026844fe7ca8d2
dir: /sys/src/9/pc/vgamga2164w.c/

#include "u.h"
#include "../port/lib.h"
#include "mem.h"
#include "dat.h"
#include "fns.h"
#include "io.h"
#include "../port/pci.h"
#include "../port/error.h"

#define	Image	IMAGE
#include <draw.h>
#include <memdraw.h>
#include <cursor.h>
#include "screen.h"

/*
 * Matrox Millennium and Matrox Millennium II.
 * Matrox MGA-2064W, MGA-2164W 3D graphics accelerators.
 * Texas Instruments Tvp3026 RAMDAC.
 */

enum {
	/* pci chip manufacturer */
	MATROX		= 0x102B,

	/* pci chip device ids */
	MGA2064		= 0x0519,
	MGA2164		= 0x051B,
	MGA2164AGP	= 0x051F
};

static void
mga2164wenable(VGAscr* scr)
{
	Pcidev *p;

	if(scr->mmio)
		return;

	p = scr->pci;
	if(p == nil || p->vid != MATROX)
		return;

	if((p->mem[0].bar & 1) != 0
	|| (p->mem[1].bar & 1) != 0)
		return;

	if(p->did == MGA2064){
		scr->mmio = vmap(p->mem[0].bar&~0x0F, p->mem[0].size);
		if(scr->mmio == nil)
			return;
		addvgaseg("mga2164wmmio", p->mem[0].bar&~0x0F, p->mem[0].size);
		vgalinearaddr(scr, p->mem[1].bar&~0x0F, 8*MB);
	}else{
		scr->mmio = vmap(p->mem[1].bar&~0x0F, p->mem[1].size);
		if(scr->mmio == nil)
			return;
		addvgaseg("mga2164wmmio", p->mem[1].bar&~0x0F, p->mem[1].size);
		vgalinearaddr(scr, p->mem[0].bar&~0x0F, 16*MB);
	}
	if(scr->paddr)
		addvgaseg("mga2164wscreen", scr->paddr, scr->apsize);
}

enum {
	Index		= 0x00,		/* Index */
	Data		= 0x0A,		/* Data */

	CaddrW		= 0x04,		/* Colour Write Address */
	Cdata		= 0x05,		/* Colour Data */

	Cctl		= 0x09,		/* Direct Cursor Control */
	Cram		= 0x0B,		/* Cursor Ram Data */
	Cxlsb		= 0x0C,		/* Cursor X LSB */
	Cxmsb		= 0x0D,		/* Cursor X MSB */
	Cylsb		= 0x0E,		/* Cursor Y LSB */
	Cymsb		= 0x0F,		/* Cursor Y MSB */

	Icctl		= 0x06,		/* Indirect Cursor Control */
};

static void
tvp3026disable(VGAscr* scr)
{
	uchar *tvp3026;

	if(scr->mmio == 0)
		return;
	tvp3026 = (uchar*)scr->mmio+0x3C00;

	/*
	 * Make sure cursor is off
	 * and direct control enabled.
	 */
	*(tvp3026+Index) = Icctl;
	*(tvp3026+Data) = 0x90;
	*(tvp3026+Cctl) = 0x00;
}

static void
tvp3026load(VGAscr* scr, Cursor* curs)
{
	int x, y;
	uchar *tvp3026;

	if(scr->mmio == 0)
		return;
	tvp3026 = (uchar*)scr->mmio+0x3C00;

	/*
	 * Make sure cursor is off by initialising the cursor
	 * control to defaults.
	 * Write to the indirect control register to make sure
	 * direct register is enabled and upper 2 bits of cursor
	 * RAM address are 0.
	 * Put 0 in index register for lower 8 bits of cursor RAM address.
	 */
	tvp3026disable(scr);
	*(tvp3026+Index) = 0;

	/*
	 * Initialise the 64x64 cursor RAM array. There are 2 planes,
	 * p0 and p1. Data is written 8 pixels per byte, with p0 in the
	 * first 512 bytes of the array and p1 in the second.
	 * The cursor is set in 3-colour mode which gives the following
	 * truth table:
	 *	p1 p0	colour
	 *	 0  0	transparent
	 *	 0  1	cursor colour 0
	 *	 1  0	cursor colour 1
	 *	 1  1	cursor colour 2
	 * Put the cursor into the top-left of the 64x64 array.
	 * The 0,0 cursor point is bottom-right, so positioning will
	 * have to take that into account.
	 */
	for(y = 0; y < 64; y++){
		for(x = 0; x < 64/8; x++){
			if(x < 16/8 && y < 16)
				*(tvp3026+Cram) = curs->clr[x+y*2];
			else
				*(tvp3026+Cram) = 0x00;
		}
	}
	for(y = 0; y < 64; y++){
		for(x = 0; x < 64/8; x++){
			if(x < 16/8 && y < 16)
				*(tvp3026+Cram) = curs->set[x+y*2];
			else
				*(tvp3026+Cram) = 0x00;
		}
	}

	/*
	 * Initialise the cursor hotpoint
	 * and enable the cursor in 3-colour mode.
	 */
	scr->offset.x = 64+curs->offset.x;
	scr->offset.y = 64+curs->offset.y;
	*(tvp3026+Cctl) = 0x01;
}

static int
tvp3026move(VGAscr* scr, Point p)
{
	int x, y;
	uchar *tvp3026;

	if(scr->mmio == 0)
		return 1;
	tvp3026 = (uchar*)scr->mmio+0x3C00;

	x = p.x+scr->offset.x;
	y = p.y+scr->offset.y;

	*(tvp3026+Cxlsb) = x & 0xFF;
	*(tvp3026+Cxmsb) = (x>>8) & 0x0F;
	*(tvp3026+Cylsb) = y & 0xFF;
	*(tvp3026+Cymsb) = (y>>8) & 0x0F;

	return 0;
}

static void
tvp3026enable(VGAscr* scr)
{
	int i;
	uchar *tvp3026;

	if(scr->mmio == 0)
		return;
	tvp3026 = (uchar*)scr->mmio+0x3C00;

	tvp3026disable(scr);

	/*
	 * Overscan colour,
	 * cursor colour 1 (white),
	 * cursor colour 2, 3 (black).
	 */
	*(tvp3026+CaddrW) = 0x00;
	for(i = 0; i < 6; i++)
		*(tvp3026+Cdata) = Pwhite; 
	for(i = 0; i < 6; i++)
		*(tvp3026+Cdata) = Pblack; 

	/*
	 * Load, locate and enable the
	 * 64x64 cursor in 3-colour mode.
	 */
	tvp3026load(scr, &cursor);
	tvp3026move(scr, ZP);
	*(tvp3026+Cctl) = 0x01;
}

VGAdev vgamga2164wdev = {
	"mga2164w",

	mga2164wenable,			/* enable */
	0,				/* disable */
	0,				/* page */
	0,				/* linear */
};

VGAcur vgamga2164wcur = {
	"mga2164whwgc",

	tvp3026enable,
	tvp3026disable,
	tvp3026load,
	tvp3026move,
};