ref: de19776b2f793de7fdf1111d84d96eb29f9a22fd
dir: /sys/src/ape/cmd/pax/config.h/
/* $Source: /u/mark/src/pax/RCS/config.h,v $ * * $Revision: 1.2 $ * * config.h - configuration options for PAX * * DESCRIPTION * * This file contains a number of configurable parameters for the * PAX software. This files should be edited prior to makeing the * package. * * AUTHOR * * Mark H. Colburn, NAPS International ([email protected]) * * Sponsored by The USENIX Association for public distribution. * * Copyright (c) 1989 Mark H. Colburn. * All rights reserved. * * Redistribution and use in source and binary forms are permitted * provided that the above copyright notice and this paragraph are * duplicated in all such forms and that any documentation, * advertising materials, and other materials related to such * distribution and use acknowledge that the software was developed * by Mark H. Colburn and sponsored by The USENIX Association. * * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. */ #ifndef _PAX_CONFIG_H #define _PAX_CONFIG_H /* Defines */ /* XENIX_286 (SCO ugh, Xenix system V(?) 286, USG with changes... * You will get a warning about DIRSIZ being redefined, ignore it, * complain to SCO about include files that are messed up or send * mail to [email protected], who can provide some patches to fix * your include files. * * Defining XENIX_286 will automatically define USG. * */ /* #define XENIX_286 /* Running on a XENIX 286 system */ /* * USG - USG (Unix System V) specific modifications * * Define USG if you are running Unix System V or some similar variant */ #define USG /* Running on a USG System */ /* * BSD - BSD (Berkely) specific modifications * * Define BSD if you are running some version of BSD Unix */ /* #define BSD /* Running on a BSD System */ /* * DEF_AR_FILE - tar only (required) * * DEF_AR_FILE should contain the full pathname of your favorite archive * device. Normally this would be a tape drive, but it may be a disk drive * on those systems that don't have tape drives. */ #define DEF_AR_FILE "-" /* The default archive on your system */ /* * TTY - device which interactive queries should be directed to (required) * * This is the device to which interactive queries will be sent to and * received from. On most unix systems, this should be /dev/tty, however, on * some systems, such as MS-DOS, it my need to be different (e.g. "con:"). */ /* #define TTY "/dev/tty" /* for most versions of UNIX */ /* #define TTY "con:" /* For MS-DOS */ #define TTY "/dev/cons" /* for Plan 9 */ /* * PAXDIR - if you do not have directory access routines * * Define PAXDIR if you do not have Doug Gwyn's dirent package installed * as a system library or you wish to use the version supplied with PAX. * * NOTE: DO NOT DEFINE THIS IF YOU HAVE BERKELEY DIRECTORY ACCESS ROUTINES. */ /* #define PAXDIR /* use paxdir.h paxdir.c */ /* * DIRENT - directory access routines (required) * * If you have Doug Gwyn's dirent package installed, either as a system * library, or are using the paxdir.c and paxdir.h routines which come with * PAX, then define dirent. * * NOTE: DO NOT DEFINE THIS IF YOU HAVE BERKELEY DIRECTORY ACCESS ROUTINES. */ #define DIRENT /* use POSIX compatible directory routines */ /* * OFFSET - compiler dependent offset type * * OFFSET is the type which is returned by lseek(). It is different on * some systems. Most define it to be off_t, but some define it to be long. */ #define OFFSET off_t /* for most BSD, USG and other systems */ /* #define OFFSET long /* for most of the rest of them... */ /* * VOID - compiler support for VOID types * * If your system does not support void, then this should be defined to * int, otherwise, it should be left undefined. * * For ANSI Systems this should always be blank. */ #ifndef __STDC__ /* #define void int /* for system which do support void */ #endif /* * SIG_T - return type for the signal routine * * Some systems have signal defines to return an int *, other return a * void *. Please choose the correct value for your system. */ #define SIG_T void /* signal defined as "void (*signal)()" */ /* #define SIG_T int /* signal defined as "int (*signal)()" */ /* * STRCSPN - use the strcspn function included with pax * * Some systems do not have the strcspn() function in their C libraries. * For those system define STRCSPN and the one provided in regexp.c will * be used. */ /* #define STRCSPN /* implementation does not have strcspn() */ /* * STRERROR - use the strerror function included with pax * * Non-Ansi systems do not have the strerror() function in their C libraries. * For those system define STRERROR and the one provided in misc.c will * be used instead. */ /* #define STRERROR /* implementation does not have strerror() */ /* /* * END OF CONFIGURATION SECTION * * Nothing beyond this point should need to be changed */ #ifdef BSD #ifdef USG #include "You must first edit config.h and Makefile to configure pax." #endif #endif /* * Do a little sanity checking */ #ifdef PAXDIR # ifndef DIRENT # define DIRENT # endif #endif #ifdef XENIX_286 # define USG #endif /* XENIX_286 */ #endif /* _PAX_CONFIG_H */ #ifndef __STDC__ #define __STDC__ #endif