shithub: riscv

ref: f39abb2923ac5faf55ce283e925671d639f3b9b9
dir: /sys/src/9/pc/usbehcipc.c/

/*
 * PC-specific code for
 * USB Enhanced Host Controller Interface (EHCI) driver
 * High speed USB 2.0.
 */

#include	"u.h"
#include	"../port/lib.h"
#include	"mem.h"
#include	"dat.h"
#include	"fns.h"
#include	"io.h"
#include	"../port/pci.h"
#include	"../port/error.h"
#include	"../port/usb.h"
#include	"usbehci.h"

static int
ehciecap(Ctlr *ctlr, int cap)
{
	int i, off;

	off = (ctlr->capio->capparms >> Ceecpshift) & Ceecpmask;
	for(i=0; i<48; i++){
		if(off < 0x40 || (off & 3) != 0)
			break;
		if(pcicfgr8(ctlr->pcidev, off) == cap)
			return off;
		off = pcicfgr8(ctlr->pcidev, off+1);
	}
	return -1;
}

static void
getehci(Ctlr* ctlr)
{
	int i, off;

	off = ehciecap(ctlr, Clegacy);
	if(off == -1)
		return;
	if(getconf("*noehcihandoff") == nil && pcicfgr8(ctlr->pcidev, off+CLbiossem) != 0){
		dprint("ehci %#p: bios active, taking over...\n", ctlr->capio);
		pcicfgw8(ctlr->pcidev, off+CLossem, 1);
		for(i = 0; i < 100; i++){
			if(pcicfgr8(ctlr->pcidev, off+CLbiossem) == 0)
				break;
			delay(10);
		}
		if(i == 100)
			print("ehci %#p: bios timed out\n", ctlr->capio);
	}
	pcicfgw32(ctlr->pcidev, off+CLcontrol, 0);	/* no SMIs */
}

static void
ehcireset(Ctlr *ctlr)
{
	Eopio *opio;
	int i;

	ilock(ctlr);
	dprint("ehci %#p reset\n", ctlr->capio);
	opio = ctlr->opio;

	/* reclaim from bios */
	getehci(ctlr);

	/* disable interrupts */
	opio->intr = 0;

	/*
	 * halt and route ports to companion controllers
	 * until we are setup
	 */
	ehcirun(ctlr, 0);
	opio->config = 0;
	coherence();

	/* clear high 32 bits of address signals if it's 64 bits capable.
	 * This is probably not needed but it does not hurt and others do it.
	 */
	if((ctlr->capio->capparms & C64) != 0){
		dprint("ehci: 64 bits\n");
		opio->seg = 0;
		coherence();
	}

	opio->cmd |= Chcreset;	/* controller reset */
	coherence();
	for(i = 0; i < 100; i++){
		if((opio->cmd & Chcreset) == 0)
			break;
		delay(1);
	}
	if(i == 100)
		print("ehci %#p controller reset timed out\n", ctlr->capio);

	opio->cmd |= Citc1;		/* 1 intr. per µframe */
	coherence();
	switch(opio->cmd & Cflsmask){
	case Cfls1024:
		ctlr->nframes = 1024;
		break;
	case Cfls512:
		ctlr->nframes = 512;
		break;
	case Cfls256:
		ctlr->nframes = 256;
		break;
	default:
		panic("ehci: unknown fls %ld", opio->cmd & Cflsmask);
	}
	dprint("ehci: %d frames\n", ctlr->nframes);

	iunlock(ctlr);
}

static void
setdebug(Hci*, int d)
{
	ehcidebug = d;
}

static void
shutdown(Hci *hp)
{
	int i;
	Ctlr *ctlr;
	Eopio *opio;

	ctlr = hp->aux;
	ilock(ctlr);
	opio = ctlr->opio;

	/* disable interrupts */
	opio->intr = 0;

	/* controller reset */
	opio->cmd |= Chcreset;
	coherence();
	for(i = 0; i < 100; i++){
		if((opio->cmd & Chcreset) == 0)
			break;
		delay(1);
	}
	if(i >= 100)
		print("ehci %#p controller reset timed out\n", ctlr->capio);
	delay(100);
	ehcirun(ctlr, 0);
	opio->frbase = 0;
	iunlock(ctlr);
}

static Ctlr*
scanpci(void)
{
	static Ctlr *first, **lastp;
	Ctlr *ctlr;
	Pcidev *p;
	Ecapio *capio;
	uvlong io;

	if(lastp != nil)
		return first;
	lastp = &first;

	p = nil;
	while ((p = pcimatch(p, 0, 0)) != nil) {
		/*
		 * Find EHCI controllers (Programming Interface = 0x20).
		 */
		if(p->ccrb != Pcibcserial || p->ccru != Pciscusb)
			continue;
		switch(p->ccrp){
		case 0x20:
			if(p->mem[0].bar & 1)
				continue;
			io = p->mem[0].bar & ~0xFULL;
			break;
		default:
			continue;
		}
		if(io == 0)
			continue;

		print("usbehci: %#x %#x: port %llux size %lld irq %d\n",
			p->vid, p->did, io, p->mem[0].size, p->intl);

		ctlr = malloc(sizeof(Ctlr));
		if(ctlr == nil){
			print("usbehci: no memory\n");
			continue;
		}

		capio = vmap(io, p->mem[0].size);
		if(capio == nil){
			print("usbehci: cannot map mmio\n");
			free(ctlr);
			continue;
		}

		ctlr->pcidev = p;
		ctlr->base = io;
		ctlr->capio = capio;

		*lastp = ctlr;
		lastp = &ctlr->next;
	}

	return first;
}

static int
reset(Hci *hp)
{
	Ctlr *ctlr;
	Ecapio *capio;
	Pcidev *p;

	if(getconf("*nousbehci"))
		return -1;

	/*
	 * Any adapter matches if no hp->port is supplied,
	 * otherwise the ports must match.
	 */
	for(ctlr = scanpci(); ctlr != nil; ctlr = ctlr->next){
		if(ctlr->active == 0)
		if(hp->port == 0 || hp->port == ctlr->base){
			ctlr->active = 1;
			break;
		}
	}
	if(ctlr == nil)
		return -1;

	p = ctlr->pcidev;
	pcienable(p);

	hp->aux = ctlr;
	hp->port = ctlr->base;
	hp->irq = p->intl;
	hp->tbdf = p->tbdf;

	capio = ctlr->capio;
	hp->nports = capio->parms & Cnports;

	ddprint("echi: %s, ncc %lud npcc %lud\n",
		capio->parms & 0x10000 ? "leds" : "no leds",
		(capio->parms >> 12) & 0xf, (capio->parms >> 8) & 0xf);
	ddprint("ehci: routing %s, %sport power ctl, %d ports\n",
		capio->parms & 0x40 ? "explicit" : "automatic",
		capio->parms & 0x10 ? "" : "no ", hp->nports);

	ctlr->opio = (Eopio*)((uintptr)capio + (capio->cap & 0xff));
	ehcireset(ctlr);
	ehcimeminit(ctlr);
	
	pcisetbme(p);

	/*
	 * Linkage to the generic HCI driver.
	 */
	ehcilinkage(hp);
	hp->shutdown = shutdown;
	hp->debug = setdebug;
	intrenable(hp->irq, hp->interrupt, hp, hp->tbdf, hp->type);

	return 0;
}

void
usbehcilink(void)
{
	addhcitype("ehci", reset);
}